Cleaning & Disinfecting Resources

FAQs + Resources

FAQs

Air Spa vs. Whirlpool

Info for Architects

Caregiver Resources

Skin Conditions

Cleaning & Disinfecting Resources

UV Basics

Room Measuring Instructions

Home > FAQs + Resources > Caregiver Resources > Cleaning & Disinfecting Resources

Cleaning & Disinfecting Resources

ADVANTAGE Cleaning/Disinfecting Procedures

Between Bath Cleaning Process After each bath, place the chair in the tub, then:
	Step 1: Turn black selector knob to “TUB CLEAN” and turn the other black selector knob to the “ON” position
	Step 2: Close the drain and turn the whirlpool on
	Step 3: When foamy solution comes out of the jets, wait a moment and turn the black selector knob to “RINSE"
	Step 4: Use the soapy solution to scrub the tub and chair
	Step 5: When the tub is clean, open the drain and use the shower wand to rinse the tub and chair
	Step 6: When non-soapy water comes out of the jets and the tub is completely rinsed, turn the whirlpool motor off and turn the black selector knob to “OFF”

End of Bath Day Disinfecting Process After the last bath of the day, place the tub in the chair, then:

Step 1: Turn black selector knob to “DISINFECT” and turn the other black selector knob to the “ON” position.	Step 2: Close the drain and turn the whirlpool on.

Step 3: When foamy solution comes out of the jets, allow 2-3 inches of liquid to pool in the foot well. Turn whirlpool off and turn black selector knob to “RINSE”. Turn the black selector knob to "OFF".	Step 4: Use the soapy solution to scrub the tub and chair. Leave wet for 10 minutes.

Step 5: After 10 minutes, turn black selector knob to “RINSE”. Turn the other black selector knob to the "ON" position. Push the button to turn the whirlpool motor on.	Step 6: When the water from the jets runs clear and the tub is completely rinsed, push the button to turn the whirlpool motor off. Turn the black selector knob to the "OFF" position.
	You can also download our Advantage Cleaning Process PDF.
Step 7: Open the drain and use the shower wand to rinse the tub and chair.

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

SERENITY Cleaning/Disinfecting Procedures

Between Bath Cleaning Process
After each bath:
Step 1: Turn black selector knob to “TUB CLEAN” and turn the handle on the side of the disinfecting panel clockwise to turn ON
Step 2: Close the drain and turn the whirlpool on
Step 3: When foamy solution comes out of the jets, wait a moment and turn the black selector knob to “RINSE"
Step 4: Use the soapy solution to scrub the tub
Step 5: When the tub is clean, open the drain and use the shower wand to rinse the tub
Step 6: When non-soapy water comes out of the jets and the tub is completely rinsed, turn the whirlpool motor off and turn the handle on the side of the disinfecting panel counterclockwise to turn OFF

End of Bath Day Disinfecting Process
After the last bath of the day:
Step 1: Turn black selector knob to “DISINFECT”
Step 2: Turn the handle on the side of the disinfecting panel clockwise to turn ON
Step 3: Close the drain and turn the whirlpool motor on
Step 4: When foamy solution comes out of the jets, allow 2-3 inches of liquid to pool in the foot well. Turn off the whirlpool motor and turn the handle on the side of the disinfecting panel counterclockwise to turn OFF
Step 5: Use the soapy solution to scrub the tub. Leave wet for 10 minutes.
Step 6: After 10 minutes, turn black selector knob to “RINSE” and turn the handle on the side of the disinfecting panel clockwise to ON
Step 7: Open the drain and use the shower wand to rinse the tub
Step 8: When non-soapy water comes out of the jets and the tub is completely rinsed, turn the whirlpool motor off and turn the handle on the side of the disinfecting panel counterclockwise to OFF.

email page	print page